Clubmaker 14-Degree Countersink $29.99 14-Degree Countersink Essential and recommended by manufacturers for graphite shafting: in.coning in. (countersinking) the top 1/8 in. of an investment cast iron or metal wood hosel at a 14 deg angle prevents the sharp edge of the rim from cutting into graphite fibers and causing shaft failure.

Clubmaker 48 Inch Drill Bit $17.99 48 in. Drill Bit: This extra-long 48 in. x 7/32 in. bit is great for removing debris from steel shafts when using hot rods.

Clubmaker Ball Shaped Deburrer $14.98 Ball Shaped Deburrer: The deburrer removes residual burrs that remain after the coning process. Made of solid micrograin carbide, this tool is vastly superior to the carbide-coated steel bits sold by some distributors at higher prices.

Clubmaker Iron Reamer $54.99 These tapered hosel reamers are designed to open bore of iron hosels. .355 in.

Golfsmith .375 HSS Reamer $19.99 Golfsmith .370 HSS Reamer: Use this .370 in. HSS Reamer for converting tapered iron hosel bores to .370 in. parallel, or enlarging parallel hosel bores.

Golfsmith 1/8 in. X 12 in. HSS BIT $5.99 Golfsmith 1/8 in. x 12 in. HSS BIT: This drill bit removes epoxy from the center of graphite shafts.

Golfsmith 48 X 5/32 in. Graphite Shaft Drill Bit $26.99 Golfsmith 48 x 5/32 in. Graphite Shaft Drill Bit The Golfsmith Graphite Shaft Drill Bit removes epoxy from graphite shafts.

Golfsmith Graphite Shaft Tip Abrading Tool $32.99 Golfsmith Graphite Shaft Tip Abrading Tool A great little tool for beginning clubmakers unsure how much to roughen the tip, or for experienced clubmakers simply looking for a faster, more consistent way to prep shaft tips for installation. Simply insert the shaft tip into the center of the tool and twist the tool 3-4 times - no guesswork needed and no fear of damaging the shaft. Meant for graphite shaft tips only, any diameter. Replacement brush cartridges (#8649a) are available separately.

Golfsmith Hosel Cleaner (Spiral Sleeves) $6.99 Golfsmith Hosel Cleaner with Spiral Sleeves This is the perfect tool for removing epoxy residue, cleaning the inside of clubhead hosels after shaft removal or for creating a coarse surface on the inside hosel wall for a better epoxy bond with the shaft. Its incredibly easy to use, working well with either a hand drill or multi-purpose tool. Replacement spiral sleeves (#8339) are available separately.

Golfsmith Hosel Cleaner Replacement Spiral Sleeves (Pkg of 5) $4.99 Golfsmith Hosel Cleaner Replacement Spiral Sleeves (5-pack) Replacement spiral sleeves for the Golfsmith Hosel Cleaner (#8338). 60 grit

Golfsmith Hosel Cleaning Brush Iron (Qty Of 3) $14.99 Golfsmith Hosel Cleaning Brushes - Iron (3-pack) Replacement iron brushes for the Golfsmith Hosel Cleaning Brush Set (#8625).

Golfsmith Hosel Cleaning Brush Set Wood/Iron $14.99 Golfsmith Hosel Cleaning Brush Set Wood/Iron One of the most important small tools in any clubmakers shop! This coarse-wrapped wire brush helps clean the bore of old epoxy, oil or other pollutants that can weaken the epoxy bond to the shaft. The ergonomic, hard rubber handle provides a better, no-slip grip, while the two included brushes accommodate wood and iron hosel bores. Brushes can also be used with a drill. Tip: Use with a fast evaporating solvent to ensure a totally clean bond. Replacement wood brushes (#8625a) and iron brushes (#8625b) are available separately.

Golfsmith Hosel Cleaning Brush Wood (Qty Of 3) $14.99 Golfsmith Hosel Cleaning Brushes - Wood (3-pack) Replacement wood brushes for the Golfsmith Hosel Cleaning Brush Set (#8625).

Golfsmith R Reamer $19.99 These hosel reamers are designed to open bore of woods. Letter R; .339 in..

Golfsmith Replacement Wire Brush For Stock 8649 $9.99 Golfsmith Replacement Wire Brush This replacement brush cartridge is for use with the Golfsmith Graphite Shaft Tip Abrading Tool (#8649).

Golfsmith Shaft Removal Kwik Out Set $39.99 Highly recommended by the Golfsmith Repair Department. A longtime favorite is now reintroduced at a lower price and redesigned with more reliable, more aggressive locking threads to secure the tool to the inside of the shaft. - New design is also longer in length for a better hold on longer broken shaft sections as well as provide more torque leverage for twisting out the broken shaft tip. - Set includes both Wood & Iron bits & handle. - To remove a broken-off steel shaft, heat the hosel to break the epoxy bond. Tap in the threaded tip of the Kwik Out and twist to lock. Dial the pushing nut down the Kwik Out and keep turning until the shaft tip begins to back out of the hosel. - Includes bits, washer and nut. - Lower price, redesigned with more reliable, more aggressive locking threads to secure the tool to the inside of the shaft.